Packaging: 20kg/unit or 40kg/unit (mixed components A and B)
Color: Pale milky yellow liquid after mixing.
Mixture Ratio: 1:1 (by weight)
Reference Dosage: 0.3-1.0kg/㎡
Application Conditions: The recommended operating temperature is between 10°C and 35°C. To avoid condensation, the application area must be well ventilated and the relative humidity must be less than 75%.
Mixing: During storage, individual components may slightly settle. Stir each component thoroughly before mixing.
When mixing, be sure to scrape off any material adhering to the sides and bottom of the bucket before stirring again to prevent uneven mixing.
After the two components are evenly dispersed, allow them to rest for 3-5 minutes before application. The maximum usable time is 20 minutes (at 25°C).
The viscosity of the mixture can be adjusted by diluting with water according to the substrate. The amount of water added should not exceed 5% of the total mixture.
Application Method: Brush, roller, or trowel.
Precautions: Application requires a clean, dry, and dust-free environment.
After application, the primer should form an even film on the surface. The surface condition will affect the coating amount, drying time, and recoating interval.
Shelf Life: 6 months
Storage: Store tightly closed in a cool, well-ventilated place away from moisture, sunlight, and freezing.
Safety: Handle this product with caution. Harmful or fatal if swallowed. If swallowed, seek medical attention immediately. Avoid contact with skin or eyes.
Always take precautions. Disposal of residues should comply with relevant national or local government safety regulations.
Water-based epoxy interior wall coating
Features:
1. Uses water as solvent, environmentally friendly;
3. Thixotropic and non-sagging.
Applications: Wall coatings for the food, electronics, and other industries.
Physical Parameters:
Color: Group A: Adjustable; Group B: Colorless
Combination Weight Ratio
A:B = 4:1
Potential Use Time: 40 minutes (15°C), 20 minutes (25°C), 10 minutes (35°C)
Full Curing Time: 10 days (15°C), 7 days (25°C), 4 days (35°C)
VOC Content: <2% (after mixing)
Touch Dry Time: 10 hours (15°C), 6 hours (25°C), 3 hours (35°C)
Application Instructions:
Reference Dosage: Approximately 0.30 kg/m2 (two coats)
Paint film thickness: Approximately 80 μm (one coat)
Tool cleaning: Water
Application conditions:
It is recommended to use this product above 10°C. To avoid condensation, the surface must be clean and the relative humidity must be less than 85%. During mixing and storage, Group A may slightly settle. Stir Group A thoroughly before mixing. Pour Group A and Group B into the mixing bucket in the correct proportion and mix thoroughly.
Application Method:
1. Primer: The recommended dosage of epoxy primer is 0.2 kg/m2. The specific dosage should be adjusted based on the on-site surface conditions to achieve a uniform film.
2. Midcoat: Depending on the flatness and strength of the wall surface, use epoxy midcoat mixed with quartz powder for repairing and leveling, then polish to a smooth surface.
3. Topcoat: Apply by spray, roller, or brush.
Precautions:
1. Usable life is based on a 5 kg batch. Higher temperatures or increased batch amounts will shorten the pot life.
2. Application requires a clean, dry, and dust-free environment.
Storage: Store tightly closed in a cool, ventilated place away from moisture, sunlight, and freezing.
Shelf Life: 6 months
Safety: Handle this product with caution. Harmful or fatal if swallowed. If swallowed, seek medical attention immediately. Avoid contact with skin or eyes. Always take precautions to prevent fire and explosion. Disposal of residues should comply with relevant national or local government safety regulations.
Important Notice: MCE guarantees the quality of its products. The advice and information provided here are derived from our independent laboratories and are accurate under controlled conditions. However, since we cannot directly and continuously control the use of the products, the company does not assume any direct or indirect liability arising from the use of the products, regardless of whether the advice, recommendations, plans and information provided are adopted.
Waterborne Epoxy Self-Leveling Coating
Features:
1. Water-soluble system, no organic solvents, safe, extremely low odor, and environmentally friendly;
2. High flowability, allowing for application of thick film coatings in multiple applications or in a single application.
3. High surface strength: Excellent scratch, abrasion, and impact resistance.
4. Good cost-effectiveness: Reduced construction costs, can be thickened by adding sand and used simultaneously, and can be diluted with water.
5. Excellent physical and chemical resistance: Acid, alkali, and oil resistance, reducing noise.
6. Soft or matte surface, highly decorative for uneven substrates.
7. Self-leveling coating, resulting in a smooth, even surface that's easy to clean.
Applications:
Suitable for coating new and old concrete, terrazzo, and other flooring, as well as damp surfaces. Widely used in factories, parking lots, airports, ports, power plants, hospitals, residential and public buildings, and laboratories with specialized requirements.
Physical Parameters:
Color Various
Gloss Soft, Matte
Weight Ratio: A: B = 10:3
Usage Time: 40 minutes (15°C) 20 minutes (25°C) 10 minutes (35°C)
Walk-in Time: 48 hours (15°C) 24 hours (25°C) 10 hours (35°C)
Full Curing Time: 10 days (15°C) 7 days (25°C) 4 days (35°C)
VOC Content: <2% (after mixing)
Performance Indicators:
Compressive Strength/Mpa Test Method: GB/T17671-1999 Index: ≥80
Abrasion Resistance (750g/500r)/g Test Method: GB1768-79 Index: ≤0.01
Motor Oil and Diesel Resistance Test Method: 60-day Immersion Index: No Change
20% Sulfuric Acid Resistance Test Method: 20-day Immersion Index: No Significant Change
20% Sodium Hydroxide Resistance Test Method: 30-day Immersion Index: No change
Hardness Test Method: Shore D Index: ≥3H
Flexural Strength/Mpa Test Method: GB 1042-79 Index: ≥35
Application Instructions:
Reference Dosage: 1.30-2.0 kg/m2
Film Thickness: 1.0-1.5 mm
Tool Cleaning: Water
Application Conditions:
It is recommended to use this product above 10°C with a relative humidity below 75%. During application and drying in confined spaces, maintain good ventilation.
Mixing
During storage, component A may slightly settle. Stir component A thoroughly before mixing.
When mixing, be sure to scrape off any material adhering to the sides and bottom of the bucket before re-stirring to prevent uneven mixing.
The two components must be evenly dispersed for at least 3 minutes before application. The maximum usable time is 30 minutes (at 25°C).
The viscosity of the mixture can be adjusted by diluting with water as needed, depending on the application. The amount of water added should not exceed 10% of the total mixture.
Application Method
Primer: The recommended dosage of epoxy primer is approximately 0.2kg/m2. The specific dosage should be determined based on the conditions of the substrate on site, ensuring a uniform film.
Midcoat: Depending on the flatness and strength of the substrate, apply a water-based midcoat mixed with quartz sand or quartz powder to the desired thickness.
Topcoat: Apply with a dedicated toothed trowel and assist with defoaming to ensure a uniform, bubble-free paint film.
Notes:
When the temperature rises or the amount of ingredients increases, the shelf life will be shortened accordingly.
During construction, the environment must be clean, dry, and dust-free. Control air circulation to prevent the introduction of foreign matter that could affect the surface finish.
Storage: Store sealed in a cool, well-ventilated place, away from moisture, sunlight, and frost.
Shelf Life: 6 months.
Safety: Handle this product with caution. Harmful or fatal if swallowed. If swallowed, seek medical attention immediately. Avoid contact with skin or eyes. Always take precautions to prevent fire and explosion. Dispose of residues in accordance with relevant national or local safety regulations.
Important Notice: MCE guarantees the quality of its products. The advice and information provided here are obtained from our independent laboratory and are accurate under controlled conditions. However, we cannot directly and continuously verify the accuracy of the information during product use.
Therefore, regardless of whether the suggestions, recommendations, plans and information provided are adopted or not, the company does not assume any direct or indirect responsibility arising from the use of the products.
Water-based epoxy topcoat
Features:
It is an environmentally friendly topcoat with exceptionally low odor and no volatile organic solvents; high adhesion; excellent surface strength; excellent resistance to scratches, abrasions, oil stains, acids, and alkalis; excellent cost-effectiveness; and reliable application. A water-based epoxy flooring system, combined with a primer and midcoat, reduces the possibility of blistering caused by underground moisture.
Applications:
Suitable for coating various new and old concrete, terrazzo, and other floors with damp surfaces. It is widely used in factories, parking lots, airports, ports, power plants, hospitals, residential and public buildings, and laboratories with special requirements.
Physical Parameters:
Colors: Various
Gloss: Soft, Semi-matte, Full Matt
Weight Ratio: A: B = 4:1
Potential Time: 40 min (15°C) 20 min (25°C) 10 min (35°C)
Full Curing Time: 10 days (15°C) 7 days (25°C) 4 days (35°C)
VOC content <2% (after mixing)
Touch-dry time: 10 hours (15°C) 6 hours (25°C) 3 hours (35°C)
Application instructions:
0.15-0.2 kg/m2 (one coat)
Paint film thickness: Approximately 80 μm (dry film thickness after one coat)
Tool cleaning: Water
Application conditions:
It is recommended to use this product at temperatures above 10°C, with no water on the substrate and relative humidity below 80%. Good ventilation should be maintained during application and drying in confined spaces.
Mixing:
During storage, Group A may slightly settle. Stir Group A thoroughly before mixing. Pour Group A and Group B into a mixing bucket according to the proportions and mix thoroughly.
Application Method:
1. Primer: Epoxy primer. The recommended dosage is 0.25 kg/m2. The specific dosage should be determined based on the site conditions and ensure a uniform film is formed.
2. Midcoat: Depending on the flatness and strength of the substrate, mix a water-based epoxy midcoat with quartz sand or quartz powder and apply to the required thickness.
3. Topcoat: Mix Groups A and B evenly and apply by roller, brush, or spray.
Precautions:
1. The shelf life will be shortened when the temperature rises or the amount of ingredients is increased.
2. Ensure a clean, dry, and dust-free environment during application. Control air circulation to prevent the introduction of foreign matter that could affect the surface finish.
Storage: Store sealed in a cool, well-ventilated place, protected from moisture, sunlight, and frost.
Shelf Life: 6 months
Safety: Handle this product with caution. Harmful or fatal if swallowed. If swallowed, seek medical attention immediately. Avoid contact with skin or eyes. Always take precautions to prevent fire and explosion. Dispose of residues in accordance with relevant national or local safety regulations.
Important Notice: MCE guarantees the quality of its products. The advice and information provided herein are obtained from our independent laboratory and are believed to be accurate under controlled conditions. However, since we cannot directly and continuously control the use of the products, we assume no direct or indirect liability arising from the use of the products, regardless of whether the advice, recommendations, plans, and information provided are adopted.
Waterborne Epoxy Midcoat
Features:
This is a universal midcoat for waterborne epoxy floors, improving their strength and smoothness.
Used in epoxy mortar and putty to reduce paint blistering caused by underground moisture.
Applications: Suitable for all substrates, especially for coating damp surfaces.
Physical Parameters:
Color: Colorless, Gray, or Green
Weight Ratio of A:B = 3:1
Pot Time: 60 minutes (15°C), 30 minutes (25°C), 15 minutes (35°C)
VOC Content: <2% (after mixing)
Recoat Time: 48 hours (15°C), 24 hours (25°C), 12 hours (35°C)
Application Instructions:
Reference Dosage 0.15kg/m2 (one coat) or 0.5kg/m2 (one coat, add 1-3 times the amount of mortar).
Tool Cleaning: Water
Application Conditions:
This product is recommended for use above 10°C. During application and drying in confined spaces, good ventilation should be maintained.
Mix: Pour components A and B into a mixing bucket according to the correct proportions and stir thoroughly. Then add quartz sand or quartz powder, stir thoroughly, and pour onto the primed surface.
Application Method Mix 0.5-3 times the amount of quartz sand (or quartz powder) and apply by scraping.
Precautions:
During application, the environment must be clean, dry, and dust-free.
The shelf life is based on 5kg of material. When the temperature rises or the material quantity is increased, the shelf life will be shortened accordingly.
Storage: Store sealed in a cool, ventilated place, away from moisture, sunlight, and freezing.
Waterborne Epoxy Primer
Features:
Highly permeable, can be used in wet environments
Maintains good adhesion even in wet environments;
Reduces blistering caused by underground moisture;
Applications: Particularly suitable for damp concrete, terrazzo, and other surfaces.
Physical Parameters:
Color: Group A: Light yellow, Group B: Creamy white
Weight Ratio: Group A: Group B = 2:1
Pot Time: 60 minutes (15°C), 30 minutes (25°C), 15 minutes (35°C)
Solids Content: 40±2% (after mixing)
Recoat Time: 48 hours (15°C), 24 hours (25°C) 12 hours (35°C)
Application Instructions: Reference dosage: Approximately 0.25 kg/m2
Tool Cleaning: Water
Application Conditions: It is recommended to use this product above 10°C, with no floating water on the substrate and relative humidity below 75%. During application and drying in confined spaces, good ventilation should be maintained.
Mixing: Pour components A and B into a mixing bucket in the correct proportions and mix thoroughly.
Application Method: Brush or roller application
Precautions:
The application environment must be clean, dry, and dust-free.
The primer should form an even film on the substrate. The condition of the substrate will vary the coating amount, drying time, and recoating interval.
Storage: Store in a cool, well-ventilated place in a sealed container, away from moisture, sunlight, and frost.
Shelf Life: 6 months
Safety: Handle this product with caution. Harmful or fatal if swallowed. If swallowed, seek medical attention immediately. Avoid contact with skin or eyes. Always take precautions to prevent fire and explosion. Dispose of residues in accordance with relevant national or local safety regulations.
Important Notice: MCE guarantees the quality of its products. The advice and information provided herein are derived from our independent laboratory and are believed to be accurate under controlled conditions. However, since we cannot directly and continuously control the use of the products, we assume no direct or indirect liability arising from the use of the products, regardless of whether the advice, recommendations, plans, and information provided are adopted.
